Ode to my Lendrum
I love this spinning wheel. It’s made in Canada. No, order it’s finely crafted in Canada. It folds for travel, it has a modest footprint and it flies so smoothly and quietly. I’ve spun everything from laceweight to chunky yarn with great success. It uses Scotch Tension which is a really fine adjustment with a knob, cotton cord and a rubber band. I can tighten and losen it with small movements for precision. This controls the take-up speed of the fiber onto the spindle.
It’s a double treadle (two pedals, two feet) which I am so grateful I could get instead of the single treadle. Spending a lot of time spinning and only using one foot is not optimal. With two pedals I can stop and start the wheel using my feet on the pedals. The fatigue factor is tremendously reduced and worth the extra money.
Specifications:
• Single Drive, Scotch Tension
• Wheel Diameter 19â€
• Regular Flyer Ratios: 6, 8, 10:1
• Orifice 7/16â€, 29.75†high
• Double Treadle
• 4 – 4 oz bobbins and tensioned kate
• No assembly, just unfold and attach head
• Maple hardwood with clear lacquer finish
• Weight 13 lbs
• Fast Flyer Ratios 12, 15, 17:1
• Plying Head Ratios 3, 7, 9:1
As you can see in the photos, that’s a lot of equipment standard with the wheel. I purchased four more spindles recently, and tonight I ordered the quill head so that I can try spinning cotton on this wheel. If it does that, then I will never need another wheel. The quill head only works with the double treadle. It spins at ratios of 6, 25, and 37:1. (Ratios are how many times the flyer head spins for every once the large wheel goes around. The more twists, the finer the thread you can spin. Fiber with very short staple length needs fast spinning to bing the fiber, like cotton.)
Here you can see the new bobbins I just got which I ordered in walnut, even though everything else is in maple. This was pretty much everything that came with the wheel (it did include 4 maple bobbins). The bobbins are on a lazy kate, with a scotch tension cord along the bottom of the bobbins. The piece to the right is the bracket for the regular flyer heads. On the pedals are the two flyer heads. The normal one on the right, the fast flyer on the left (you can see the smaller circles, which is where the band goes to set the ratio.) At the top of the wheel, the larger plying bobbin and bracket are attached. There are two bands, on the wheel, one is for the plying head, the other for the regular flyers. The bracket can also be raised and lowered to adjust tension to keep the bands flowing free.
I have the wheel on a piece of rubber fabric that you put under rugs to keep them from slipping. The wheel is light, so without it the wheel tends to walk a bit. I sit in a really nice padded chair we bought when we got our sewing table. The padded back is a godsend.
I have some thoughts on drop spindles as well. I have two and I still love using them. I learned on a bottom whorl and I believe that it taught me a lot in preparation to moving to a wheel. There’s something wonderfully visceral about using the drop spindle. I tend to overspin a bit on the wheel still, but the yarn I spin on the spindles now is perfectly balanced when I wind them off on the swift into a skein. I can’t wait to get to that stage with the wheel. It’s also still a lot easier to travel with a drop spindle than with the wheel.
The first spindle, on the left, I got from Heritage Spinning in Oxford. The owner, Joan, has her father make these. The channel up at the top is excellent for keeping the yarn balanced and held. It’s a very simple spindle, reasonably priced, elegantly made, and it served me really well in the beginning. The second spindle Brian got for me this past Christmas. It’s a ring spindle from Golding that can be either a top or bottom whorl. I’ve tried spinning from a top and I don’t like it as well as a bottom, which is slower. This has some incredible features, like the notches in the ring to keep the fiber from slipping and the hook at the top works like a champ. It’s beautifully weighted, but because of this, it requires understanding what a fiber needs for spinning. For example, it’s too heavy for cotton. The spindle on the left, my first one, has a little bit of recycled cotton denim I tried spinning. The spindle is still a little heavy and that makes for a very uneven thread. Cotton can easily take 1000 twists per inch and the drop spindle just can’t quite go fast enough.
I am enjoying everything about spinning. It’s easier and often times cheaper to go and buy yarn, but I really love knowing how much a part of the process I’ve been.